Trends in Mechanical Engineering & Technology
Volume 6, Issue 2 (2016)
Published
Table of contents
-
Evaluation of Heat Flow Parameters of Resistance Spot Welding for Stainless Steel SS304
Abstract: Resistance spot welding is a popular metal joining process, which is widely used in automobile industry, household and domestic appliances manufacturing industry and fabrication industry like air craft manufacturing industries [1, 2]. Experimental investigation was carried out on inner and outer sleeve, which is used in stove manufacturing industry. Material taken was stainless steel SS304 having thickness 0.5 mm for experiment. Experimental investigation was based on two defects, which are …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 1–10 Read article
-
Influence of Process Parameters of TIG Welding Process on Mechanical Properties of SS304L Welded Joint: A Review
Abstract: The purpose of this study is to study the effects of various process parameters (welding current, filler materials and groove design) of tungsten inert gas welding (TIG) on aspect ratio, hardness and impact strength of SS304L welded joint. Aspect ratios are obtained by taking the ratio of bead width and bead penetration. This bead dimensions can be measured by digital vernier calipers. Weld joint quality depends on the bead dimensions. …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 11–17 Read article
-
Thermo-Mechanical Analysis of Aluminium and Mild Steel during Friction Drilling
Abstract: Friction drilling is a non-machining method of making holes in metal, in which the material is melted by adding high pressure and friction energy. Friction drilling uses very heat resistant cemented carbide, pointed but not sharp object. This device is pressed against a target material with both high rotational speed and high pressure. The process reshapes all thematerial so that no material is lost. The sleeve that is about three …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 18–24 Read article
-
Current Trends in Optimization of Parameters of Electric Discharge Machining Process: A Review
Abstract: Wire-cut electrical discharge machining (EDM) is an emerging machining process for machining hard-to-machine materials and intricate shapes which are impossible to make with conventional machining process. The optimum selection of input parameters for the wire electrical discharge machining (WEDM) process is based mainly on the technology used and experience of the operator. This paper reviews the effect of most significant input process parameters of WEDM such as pulse on, pulse …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 25–33 Read article
-
Experimental Investigation of PTFE Composite Material with Different Filler Materials
Abstract: Experimental investigation of PTFE (Polytetrafluroethylene) composites with different filler materials such as glass fiber, molybdenum disulphide, graphite carried is out in this study. This study exhibits tribological properties such as wear and coefficient of friction of PTEF composite material. Pin on disc tribometer is used to conduct the wear on PTFF polymer composite. Test is conducted on 10 mm diameter PTFE pin against EN31 counter face. Wear and friction experiment …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 34–42 Read article
-
An Overview of Crack and Damage Detection Using Various Techniques
Abstract: In present time, researchers have given observations on damage detection techniques using different types of methods. Importance in several damage detection techniques has significantly improved over the past two decades and numerous detection techniques created on model study methods have been established. Crack damage detection and condition observing of configurations have developed ever-increasing concerns. Generally best accessible techniques are constructed on visual review or localized valuation processes such as acoustic, …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 43–50 Read article
-
Ecofriendly Foundry Sand Binders: A Review
Abstract: The casting process is the most versatile manufacturing process. It involves pouring of metal into a mould, thus the mold material and molding method must be selected with care. Resin bonded sand casting is a high demanding technology due to its good surface finish, dimensional stability and shakeout characteristics. This paper reviews the different types of binders used in casting process to produce moulds. The Foundry industry has found itself …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 51–58 Read article
-
Evaluation of Epoxy Granite as an Alternate Material for Lathe Bed
Abstract: Machine Tool is a machine that gives the desired shape to the work with required accuracy of removing metal from the work in the form of chip. Beds, columns, bases, head stock are known as ‘structure’ in a machine tool. The Lathe Bed should be sufficiently rigid to prevent deflection under tremendous cutting pressure transmitted through the tool-post and carriage to the Lathe Bed. It must be massive with sufficient …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 59–68 Read article
-
Investigation of Mechanical Properties of Al356 Metal Matrix Composites
Abstract: Normal 0 false false false EN-IN X-NONE X-NONE Nowadays there is a constant need for the improvement of properties of materials due to their ever increasing demands according to their applications because of those requirements all fields are concentrating on composite materials which are less weight to density ratios having high strength good hardness etc. based on that this paper deals with the fabrication and investigation of mechanical properties of …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 69–74 Read article
-
Optimization of Green Sand Casting Process Parameters by Artificial Neural Network
Abstract: In this paper, artificial neural network (ANN) is used to train the network which can predict the casting defect. L27 orthogonal array is used as input matrix for training of neural network. NN tool is used to train the network for prediction of defects. Major defects observed on shop floor were; misrun, blowholes, inclusions and porosity. Moisture, permeability, LOI, compressive strength, volatile content, vent holes, pouring time, pouring temperature, mould …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 75–80 Read article
-
Structural Vigor Comparison of a CNG Cylinder with Different Material Cull
Abstract: The present research deals with the structural analysis of a CNG cylinder being utilized in conveyances as fuel source. The portable CNG cylinders are being utilized in conveyances due to their preponderation in vigor, weight advantage, and lower engenderment costs. A design of cylinder is first presented for which the research is performed. Then, a finite element model of the vessel is utilized to estimate whether the current design has …
Published in Trends in Mechanical Engineering & Technology · Vol. 6, Issue 2, 2016 · pp. 81–88 Read article