Volume 5, Issue 3 (2018)
Published
Table of contents
-
CFD and Performance Analysis of Vortex Tube
Abstract: A vortex tube cooling system has been designed and constructed in order to make a performance test. To be serve the effect of various parameters on performance several number of vortex tubes have been constructed throughout this work. These vortex tubes have been tested at various parameters to make comparison between them. The flow analysis inside a vortex tube is highly complex mainly due to 3D flow structure involving secondary …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 1–14 Read article
-
Prospects for creating software to ensure the life cycle of waste processing
Abstract: The priority direction in the processing of waste from existing production is not only the creation or upgrading of technology for processing, but also - the development of software for modeling installations. Also, the current procedure for the storage of solid domestic waste requires information support of the product life cycle. A means - modernization of modern software ERP-systems. At present, in Russia, the main types of software being developed …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 15–19 Read article
-
Redesigning the Pump Assembly Layout to Enhance the Productivity
Abstract: This paper discusses the productivity improvement in pump layout. The whole paper deal with the causes for higher cycle time in the production of pump and developing the efficient and effective layout. To accomplish the goal, analyse the cycle time of all work stations by the help of stop watch, with the help of the assembly worker and stop watch the data is collected. The cycle time graph are drawn …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 20–26 Read article
-
Study and Analysis of Sewing Section in Garment Industry
Abstract: The production process in a garment industry is categorized into Fabric sourcing, Cutting and bundling, sewing, finishing and dispatching. Sewing section is the most important and critical process, the garment is completed and is suitable to be worn. Rolls of fabric which are cut and folded are sewn to specific three dimensional shapes in very complex ways require a high level of skill and experience. For maximum production in the …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 27–33 Read article
-
Textile Treatment processes using Plasma as the Fourth State
Abstract: Green Treatment of Textiles using Fourth State Plasma Technologies is on the focus worldwide with promising environmental incentives. As reported globally, the latest technology of the century being the Plasma Technology has been applied to Textiles almost in all fields from production, processing and treatment. The textile material will be awarded with special properties on processing or treating through the Plasma technology.
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 34–36 Read article
-
Design and Thermal Analysis of Fins for Air Cooled Engine by Varying its Geometry
Abstract: An air-cooled motorcycle engine releases heat to the atmosphere through the mode of convection to facilitate this, fins are provided on the outer surface of the cylinder. The cooling fins allow the wind to move the heat away from the engine. The heat transfer rate depends upon the velocity of the vehicle, fin geometry and the ambient temperature. Low rate of heat transfer through fins is the main problem of …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 37–53 Read article
-
To Evaluate the Effect of Vehicle Aerodynamics on the Drive Layout of Vehicle
Abstract: Nowadays, with the increase in competition in automobile sector, vehicle aerodynamics play an important role. Aerodynamics affects the performance of the vehicle due to changes in parameters such as downforce, drag forces and coefficient of drag which play a significant role at high speed. In this research paper downforce and drag force of vehicle are determined by analytical and numerical analysis of flow of air around it. For modeling of …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 54–63 Read article
-
TO FIND A CLMPING FORCE OF DOUBLE SIDED SINGLE ANGLE EXPANDING COLLET USING ANSYS MECHANICAL
Abstract: The subject of Production deals with the use of fixtures that ensure repeatability to the work piece to be manufactured. The fixture is a clamping device that mounts parts at perfect location and gives stability, which leads to mass production. This type of clamping plays a decisive role in getting good reliability of the product. Collet is one of the clamping devices which has long slits around its periphery, widely …
Published in Trends in Machine design · Vol. 5, Issue 3, 2018 · pp. 64–70 Read article