Journal of Materials & Metallurgical Engineering
Volume 3, Issue 1 (2013)
Published
Table of contents
-
A Novel Technique for Improved Recovery of Mg-Analysis of the Microstructure and Physical Properties
Abstract: Aluminium-Magnesium alloys are used widely in industrial applications as well as for the preparation of metal matrix composite because of their low density and high specific strength. Magnesium has a low boiling point and the recovery of magnesium is poor when it is added in pure form particularly as cheaply available turnings to the liquid metal. Magnesium is added to aluminium for increasing its wettability and thus helping in uniformly …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 1–7 Read article
-
Multi Objective Optimization of Weld Bead Geometry Parameters of Pulsed Current Micro Plasma Arc Welded Inconel 625 Using Enhanced Non-dominated Sorting Genetic Algorithm
Abstract: Pulsed Current Plasma Arc Welding (PCPAW) is one of the most widely used welding processes in sheet metal manufacturing industry. In any fusion arc welding process, the weld bead geometry plays an important role in determining the mechanical properties of the weld and hence, quality of the weld. Moreover, the geometry of weld bead involves several simultaneously multiple quality characteristics such as front width, back width, front height and back …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 17–24 Read article
-
Processing and Properties of In situ Synthesized Reinforcements in Molten Magnesium
Abstract: In situ synthesized reinforcements for magnesium composites are an attractive area of research especially due to the inherent advantages of the process. Various reinforcements such as intermetallics and ceramics have proved their effectiveness in magnesium by imparting higher mechanical and tribological properties to the metal matrix. Fabrication of reinforcements in molten magnesium matrix is a very critical area owing to large scale production prospective and ease of implementation. This paper …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 25–33 Read article
-
Response of Sea Water Immersed GFRP Composite to Thermal Shock
Abstract: The work involves examining the effects of sea water immersion and temperature fluctuations, precisely that of up and down thermal shocks (lower to higher and vice-versa), on the glass fiber /epoxy laminated composites. These effects are studied in terms of sea water absorption, degradation in inter laminar shear strength (ILSS), alternations in the glass transition temperature (Tg) as compared to the untreated samples and finally listing up of the mode …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 34–41 Read article
-
Review of Nitrite Inhibitor for Protection of Rebar Corrosion
Abstract: Load bearing concrete structures need steel reinforcement (rebar) strips or rods, which are prone to attack by the corrosive environment inside the concrete due to constant ingress of moisture, pollutant gases and anions (mainly Cl-, SO4- -). One of the means of reducing such type of corrosion is the use of inhibitors. Inhibitors are water soluble but film forming on metals by their selective adsorption on the metal surface. These …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 42–56 Read article
-
Effect of Alloying Elements and Processing Parameters on Mechanical Properties of Austempered Ductile Iron
Abstract: In the present work, austempering is carried out for three different grades (Unalloyed, copper alloyed and Nickel alloyed) of ductile iron. After that the variation of mechanical properties (Hardness, Tensile strength and Elongation) and microstructure of the austempered ductile iron (ADI) with alloying elements (Copper and Nickel) and austempering process variables (austempering temperature and austempering time) were studied. It is found that, with increasing austempering time hardness, tensile strength and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 3, Issue 1, 2013 · pp. 8–16 Read article