Journal of Materials & Metallurgical Engineering
Volume 15, Issue 3 (2025)
Table of contents
-
Exploring the Luminescent Behavior of Dysprosium-Doped Halo-sulphate Compounds
Abstract: In essence, this study aims toward understanding the photo-luminescent properties of Dy³⁺ halogenated sulfates, viz., synthesis, characterization, and luminescent behavior of the materials. Dysprosium ions are introduced into the halo-sulfate matrices to investigate their suitability for solid-state lighting applications. The aim of the study is to explain the mechanisms of the photo luminescence of Dy³⁺ and study the influence of the doping concentration on luminescence efficiency and the thermal stability …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 01–06 Read article
-
Gas Sensors Fabricated using Carbon Powder Derived from Dried Banana Peels Waste to detect Methanol, Ethanol, Acetone Vapors and Carbon Dioxide Gas
Abstract: Low cost and environmentally friendly activated carbon powder was synthesized using waste banana peels. Phosphoric acid was utilized as activation agent. Doctor blade method was employed to fabricate films of activated carbon on conductive or nonconductive glass substrates. Films were subsequently annealed at 70 0C for 30 minutes in air. According to XRD patterns, single phase of activated carbon was crystallized in thin film form. Carbon prepared from banana peels …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 14–25 Read article
-
Innovative Design and Implementation of PCD-Based Drawing Dies and Tungsten Carbide Molds for Automotive Fastener Manufacturing
Abstract: This study presents an integrated engineering investigation into the design, optimization, and implementation of advanced tungsten carbide and polycrystalline diamond (PCD) tooling technologies within the cold forging and wire drawing processes at Koobesh Kavir Semnan Company, one of Iran’s leading automotive fastener manufacturers. By combining powder metallurgy principles, material flow simulation, and experimental validation, this research introduces a technological advancement that improves productivity, tool longevity, and cost-efficiency in industrial production. …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 16–26 Read article
-
Heat Transfer Analysis Between Two Aluminium Parallel Plates With Natural Convection
Abstract: As a type of energy, heat can be transferred from heated systems using the natural convection heat transfer method, which has several uses in different industries. Natural convection method of heat conveyance is suitable in many cases due to absent of any external sources like fan. The transfer of this kind of energy can be listed as electrical and electronics equipment, nuclear reactors, domestic convection, dry cooling towers, thermo siphons, …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 26–34 Read article
-
Short Review: The Expanding Role of Shape Memory Alloys in Technology and Medicine
Abstract: Shape Memory Alloys (SMAs) are a unique class of smart materials that can recover their original shape when exposed to specific stimuli, such as temperature or magnetic fields. This exceptional property, attributed to the martensitic phase transformation, has garnered significant interest in various industries. SMAs exhibit remarkable characteristics such as pseudoelasticity, high corrosion resistance, excellent biocompatibility, and superior fatigue strength, making them ideal for applications in biomedical, aerospace, automotive, and …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 35–44 Read article
-
Substitution of La3+ in Cu0.5Co0.5 LaxFe2-x O4 (x=0.02, 0.06) spinel ferrites improves the structural and dielectric Properties
Abstract: Nanosized Spinel ferrites with composition Cu0.5Co0.5 LaxFe2-x O4 (x=0.2, 0.6) synthesized by Sol-Gel auto Combustion method. The prepared sample was calcinated at 8000c for 4 hours. The substitution of La3+ effects the structural parameters, which is characterized by X-ray diffraction (XRD). The X-rd analysis shows that the crystallite size is 34.609 nm for 0.02 and 38.994 nm for 0.06 was calculated by using Debye-Scherrer’s formula. dislocation density shows at value …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 45–48 Read article
-
Analysis aspects of pressure tank: A review
Abstract: This review paper presents a detailed analysis of pressure vessels, focusing on finite element analysis (FEA) to evaluate structural integrity. Pressure vessels are widely used in industries such as chemical processing, power plants, and oil refineries, where they are subjected to extreme temperature and pressure conditions. Ensuring their safe and efficient operation requires a thorough understanding of stress distribution, deformation characteristics, and failure mechanisms. This study reviews existing research on …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 49–55 Read article
-
Design and Implementation of 256-bit Vedic Multiplier on Reconfigurable Platform
Abstract: Multiplication is a fundamental arithmetic operation in digital signal processing and embedded systems. Traditional multiplier architectures often suffer from increased latency and resource utilization when scaled to higher bit widths. Vedic Mathematics, an ancient Indian technique, offers a novel and efficient alternative. This paper presents the design and implementation of a 256-bit Vedic multiplier using the Urdhva Tiryakbhyam Sutra on a reconfigurable hardware platform, specifically FPGA. The proposed architecture decomposes …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 56–65 Read article
-
Carbon-Based Supercapacitors Evolutionizing EVs
Abstract: The relentless pursuit of efficiency in transportation, particularly in electric and hybrid vehicles, hinges on sophisticated energy management systems. Regenerative braking, a technology that offers a significant opportunity for improving fuel economy and extending battery life. However, the effectiveness of regenerative braking is often hampered by limitations in energy storage systems. Traditional batteries, while excellent for sustained energy delivery, struggle with the rapid charge and discharge rates required by aggressive …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 66–76 Read article
-
Comparative Analysis of 3D Printed Nylon and PETG Specimens for Mechanical Properties.
Abstract: Fused deposition modeling (FDM) is one of the most used additive manufacturing techniques for polymer components. The polymer materials generally used in FDM process are polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), polyethylene terephthalate glycol (PETG), Nylon, etc. The mechanical properties of parts fabricated by FDM depend on material and process parameters. Several researchers have tried to investigate the influence of process parameters on mechanical properties for some of the …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 7–14 Read article
-
Comparative Analysis of Natural and Synthetic Fibre-Reinforced Composites: Mechanical Properties, Processing, and Sustainability Considerations
Abstract: The development of fibre-reinforced composites has significantly advanced engineering applications due to their excellent strength-to-weight ratio, corrosion resistance, and versatility. Synthetic fibres such as glass and carbon provide superior mechanical performance, but their production is energy-intensive and environmentally harmful. Natural fibres, including jute, flax, banana, and hemp, offer biodegradability, lower cost, and sustainability benefits, though they often fall short in strength and durability. Hybrid composites frequently demonstrate improved performance by …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 77–95 Read article
-
Bio Materials and Nanotechnology: Green Tea (Waste)– Aluminium Nanoparticles (Gt-Al Nps) For Methylene Blue Adsorption
Abstract: This study examines the adsorption of Methylene Blue (MB) dye from aqueous solutions using Aluminium Nanoparticles synthesized with green tea powder as a biological reducing agent. Methylene Blue, an aromatic phenothiazine dye, is widely applied in medical diagnostics and various industrial processes, but its uncontrolled release into water bodies leads to environmental pollution due to its intense colour, stability, and potential toxicity. Therefore, identifying an efficient and eco-friendly adsorbent for …
Published in Journal of Materials & Metallurgical Engineering · Vol. 15, Issue 3, 2025 · pp. 96–107 Read article