Journal of Mechatronics and Automation
Volume 5, Issue 1 (2018)
Published
Table of contents
-
A Study on Chatter Marks in Crankshaft Pin Grinding Process Using Taguchi Technique
Abstract: Crankshaft pin grinding is a vital machining process in automotive industry. It is a finishing operation to the crankshaft of the engine, which if neglected could lead to a significant cost to the manufacturer of warranty claims. The study aims at identifying significant process parameters that are influencing the chatter marks and also setting the process parameters of the machine to get a good quality product. Chatter marks are the …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 1–5 Read article
-
Experimental Investigation of Process Parameters While Milling of AA8011 Using MCDM/MADM Method-TOPSIS
Abstract: This paper presents in-depth and comprehensive approach for optimizing the machining parameters in milling of wrought alloy AA8011 using a MCDM/MADM method called TOPSIS. The present work is carried out in three phases; in the first phase the orthogonal array L27 design is prepared using Minitab software by considering various milling parameters such as speed, feed and depth of cut at three different levels. In the second phase, milling operations …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 11–16 Read article
-
Analysis and Design of Frequency Reconfigurable Microstrip Patch Antenna using PIN Diode
Abstract: A reconfigurable antenna provides modify dynamically its frequency and radiation properties, which will provides the intentional redistribution of the RF currents over the antenna surface. Also this type of antennas provides the dynamical response. The difference between the smart antennas is its lies inside the antenna rather than in an external beamforming network. The proposed structure was simulated by using the High Frequency Structure Software (HFSS) version 15.0. The simulated …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 17–23 Read article
-
Design and Implementation of a Long Range Decentralized Vehicular Network
Abstract: The paper proposes a technique for establishing a long range decentralized vehicular ad-hoc network, with the aim to solve on-road traffic problems faced by drivers and other stakeholders such as cyclists and pedestrians. The proposed technique doesn’t make use of internet connectivity and hence is suitable for both, underdeveloped and developing countries as well. The technology can also be used for navigation purposes and sensing the environment (surrounding vehicles) for …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 24–30 Read article
-
Optimization of Multiple Responses in Turning of AA7075 Using Taguchi’s Quality Loss Method
Abstract: The present work is to explore the affect of turning parameters, speed, feed and depth of cut on the multiple performances of Material Removal Rate and Surface Roughness characteristics. AA7075 is considered as the work piece as it has extensive applications in the field of aerospace and marine sectors. The experiments are carried out using tungsten carbide tool of 0.4 nose radius and as per the standard Taguchi’s L9 Orthogonal …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 31–37 Read article
-
Drip Irrigation Pipe Manufacturing Process and Defects in It- A Review
Abstract: In the development phase of drip pipe, conventional procedures for pipe extrusion line setup process were based on tryouts and then decisions to change the process parameters were made to minimize the errors occurring in pipe extrusion process of drip pipe. Every line setup needed the same methodology and hence loss of valuable time and material scrap. The variation of raw material supplies is also considered in this optimization process. …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 38–48 Read article
-
Optimization of Process Parameters in Wire EDM of HCHCrD2 using RSM-based Multi-objective Genetic Algorithm
Abstract: While precision is of paramount importance in machining of high strength conductive materials, Wire Electrical Discharge Machining (WEDM) is preferred. In the present work, experimental study has been carried to identify the appropriate process parameter settings for wire electrical discharge machining of high carbon high chromium D2 steel (HCHCrD2). The process parameters such as pulse peak current, pulse duration, pulse-off time, wire feed, wire tension and flushing pressure are considered. …
Published in Journal of Mechatronics and Automation · Vol. 5, Issue 1, 2018 · pp. 6–10 Read article