Journal of Experimental & Applied Mechanics
Volume 8, Issue 3 (2017)
Published
Table of contents
-
Stress and Deformation Analysis of Rotating Cylindrical Pressure Vessel of Functionally Graded Material Modeled by Mori-Tanaka Scheme
Abstract: The present study deals with the linear elastic analysis of rotating cylindrical pressure vessels. The vessels are made up of one directional functionally graded material (FGM), in which mechanical and physical properties are varying along the radial direction. The analysis is carried out using finite element method which is based on the principle of stationary total potential (PSTP). Material properties are graded according to the Mori-Tanaka distribution law and ceramic-metal …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 1–7 Read article
-
An Investigation of Stress and Deformation States of Rotating Functionally Graded Spherical Pressure Vessels
Abstract: The present study deals with the analysis of rotating spherical pressure vessels made of functionally graded materials (FGMs). Material properties are graded along the radial direction, which is achieved by varying volume fractions of the constituting materials according to Mori-Tanaka scheme. Shells are subjected to hydrostatic internal pressure and have free boundary condition at the outer surface. Governing equations are derived using principle of stationary total potential. The effects of …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 19–27 Read article
-
Mechanical and Tribological Properties of Cr3C2-NiCr Coated Ti6Al4V Implant Alloy
Abstract: Ti6Al4V alloys are widely used in medical and aerospace applications due to their superior mechanical properties. But, Ti6Al4V alloys are poor in tribological properties such as wear. Poor wear resistance consequences in the formation of wear debris in human implants and leads to inflammation and pain. In this work, Cr3C2-NiCr coatings were applied to improve the mechanical properties such as tensile strength, hardness and tribological properties such as wear resistance. …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 28–42 Read article
-
Effect of Post Weld Heat Treatment on Mechanical Properties and Microstructure of P11 Weld: A Review
Abstract: Post weld heat treatment (PWHT) is a process of reducing residual stresses and enhancing material properties of any material after welding. The process depends on many parameters like type of material, thickness of material, PWHT temperature, soaking time, heating and cooling rate, etc. Post weld heat treatment is a process of material that could result detrimental effects on tensile strength, yield strength, impact toughness, hardness, elongation, etc. If the process …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 43–47 Read article
-
Minimization of Distortion During Gas Metal Arc Welding Process: A Review
Abstract: The gas metal arc welding (MIG) process is widely used in many appliances because of its versatility. For GMAW process, metals like carbon steel, stainless steel, aluminium, copper, low-alloy steel are widely used in all positions. Butt joint, lap joint, T-joint, edge joint, corner joint are the common types of joints used in welding. The change of shape and dimensions that occur after welding is known as distortion that leads …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 48–53 Read article
-
Isogeometric Topology Optimization of Continuum Structures using Evolutionary Algorithms
Abstract: Isogeometric analysis is a popular method for the analysis of problems involving complex geometry and governed by differential equations. Meta-heuristics are widely used to determine the optimum distribution of material within the given design domain. The focus of this study is to perform isogeometric topology optimization of continuum structures using meta-heuristics nature inspired firefly algorithm. NURBS basis functions are used to construct the geometric model and to calculate the displacements …
Published in Journal of Experimental & Applied Mechanics · Vol. 8, Issue 3, 2017 · pp. 8–18 Read article